OQT350-R200-2EP-IO-0,3M-V31-L Pepperl + Fuchs Electronic Components

Product Details

• Light source
  laser diode
• Diagnostic Coverage (DC)
  0 %
• Transfer rate
  COM2 (38.4 kBit/s)
• Signal output
  2 push-pull (4 in 1) outputs, short-circuit protected, reverse polarity protected, overvoltage protected
• Switching voltage
  max. 30 V DC
• Housing height
  50.6 mm
• Detection range
  60 ... 350 mm
• Beam divergence
  > 5 mrad, d63 < 2,8 mm in the range of 350 mm ... 800 mm
• Mission Time (TM)
  20 a
• Control elements
  Teach-In key
• Switching frequency
  217 Hz
• Storage temperature
  -40 ... 70 °C (-40 ... 158 °F)
• Mass
  approx. 41 g
• Detection range min.
  60 ... 100 mm
• Pulse length
  5.5 µs
• Diameter of the light spot
  approx. 3 mm at a distance of 350 mm
• No-load supply current
  < 16 mA at 24 V supply voltage
• Min. cycle time
  2.3 ms
• Voltage drop
  ≤ 1.5 V DC
• FDA approval
  IEC 60825-1:2014 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007
Cable length
0.3 m
Light type
modulated visible red light
Note
LASER LIGHT , DO NOT STARE INTO BEAM
Ambient light limit
EN 60947-5-2 : 45000 Lux
Black-white difference (6 %/90 %)
< 2 %, ,
Operating voltage
10 ... 30 V DC
Ripple
max. 10 %
Switching current
max. 100 mA , resistive load
Usage category
DC-12 and DC-13
EAC conformity
TR CU 020/2011
CCC approval
CCC approval / marking not required for products rated ≤36 V
Degree of protection
IP67 / IP69 / IP69K
Connection
fixed cable 300 mm with M8 x 1 male connector; 4-pin
Detection range max.
40 ... 400 mm
Adjustment range
100 ... 350 mm
max. pulse energy
< 40 nJ
MTTFd
560 a
IO-Link revision
1.1
Protection class
III
SIO mode support
yes
Compatible master port type
A
Response time
2.3 ms
Laser safety
EN 60825-1:2014
Housing width
15 mm
Housing
PC (Polycarbonate)
Reference target
standard white, 100 mm x 100 mm
Repetition rate
approx. 2.4 kHz
Opening angle
approx. 0.3 °
Function indicator
LED yellow: constantly on - switch output active, constantly off - switch output inactive
Device profile
Identification and diagnosis, Smart Sensor type 0
Device ID
0x111802 (1120258)
Switching type
The default setting is: C/Q - Pin4: NPN normally open, PNP normally closed, IO-Link, Q2 - Pin2: NPN normally-open, PNP normally-closed
Communication interface
IEC 61131-9
UL approval
E87056 , cULus Listed , class 2 power supply , type rating 1
Housing depth
41.7 mm
Optical face
PMMA
Laser class
1
Wave length
680 nm
Operation indicator
LED green: constantly on - power on, flashing (4Hz) - short circuit, flashing with short break (1 Hz) - IO-Link mode
Interface type
IO-Link ( via C/Q = pin 4 )
Process data width
Process data input 2 Bit, Process data output 2 Bit
Product standard
EN 60947-5-2
Ambient temperature
-40 ... 60 °C (-40 ... 140 °F) , fixed cable, -20 ... 60 °C (-4 ... 140 °F) , movable cable not appropriate for conveyor chains

OQT350-R200-2EP-IO-0,3M-V31-L Related Documents