RSS 36-I2-SD-ST Schmersal Electronic Components

Product Details

• Short-circuit recognition
  Yes
• Terminal Connector
  Connector M12, 8-pole
• Storage and transport temperature, maximum
  +85 °C
• Protection rating
  III
• Active principle
  RFID
• Time to readiness, maximum
  2,000 ms
• Safety functions
  Yes
• Note (Repeat accuracy R)
  Axial offset: The long side allows for a maximum height misalignment (x) of sensor and actuator of 8 mm (e.g. mounting tolerance or due to guard door sagging). The axial misalignment (y) is max. ± 18 mm (see figure: Operating principle). Minimum clearance
• Storage and transport temperature, minimum
  -25 °C
• Rated insulation voltage Ui
  32 VDC
• Rated operating voltage, maximum
  26.4 VDC
• Housing construction form
  Block
• Enclosure material
  Plastic, glass-fibre reinforced thermoplastic, self-extinguishing
• Number of Series-wiring of sensors
  31
• Ensured switch distance ON Sao
  10 mm
• Ambient temperature, maximum
  +70 °C
• Resistance to vibrations to EN 60068-2-6
  10 … 55 Hz, amplitude 1 mm
• Rated operating voltage, minimum
  20.4 VDC
• Current, Utilisation category DC12
  0.25 A
• Current, Utilisation category DC13
  0.25 A
Installation conditions (mechanical)
not flush
Serial diagnostics
Yes
Number of LEDs
3
Note
The cable section of the interconnecting cable must be observed! Cable length and cable section alter the voltage drop depending on the output current
Ambient temperature, minimum
-25 °C
Overvoltage category
III
general information
Individual coding, multiple teaching
Diagnostic output
Yes
Actuating panels
lateral
Ensured switch distance OFF Sar
20 mm
Height of sensor
25 mm
Restistance to shock
30 g / 11 ms
Rated operating voltage
24 VDC −15 % / +10 %
Versions
p-type
Duration of risk, maximum
200 ms
Cascadable
Yes
Active area
lateral
Repeat accuracy R R
0.5 mm
Material temperature resistance of the cable (at rest), minimum
-30 °C
No-load supply current I0
100 mA
Required rated short-circuit current to EN 60947-5-1
100 A
Voltage drop Ud, maximum
2 V
Standards
IEC 60947-5-3
Reaction time, maximum
100 ms
Number of fail-safe digital outputs
2
Switch distance
12 mm
Degree of protection
IP65 to EN 60529, IP67 to EN 60529, IP69 to EN 60529
Sensor topology
Sensor for series wiring
Gross weight
250 g
Number of semi-conductor outputs with signaling function
1
Length of sensor
22 mm
Material temperature resistance (long-term), maximum
+105 °C
Coding level according to ISO 14119
High
Integral System Diagnostics, status
Yes
Short circuit detection
Yes
Hysteresis (Switch distance), maximum
2 mm
Width of sensor
106.3 mm
Material temperature resistance of the cable (in motion), minimum
-10 °C
Degree of pollution to VDE 0100
3
Rated operating current (safety outputs)
250 mA
Mounting
A screw length of 25 mm is sufficient for sensor mounting and for side mounting of the actuators. 30 mm long screws are recommended when the actuator is mounted upright and/or when the sealing discs are used.
Switching frequency, approx.
1 Hz
Voltage, Utilisation category DC12
24 VDC
Rated impulse withstand voltage Uimp
0.8 kV
EMC rating
IEC 60947-3
Voltage type
DC (direct current)
Output current, (fail-safe output), maximum
0.25 A
Operating current
150 mA
Voltage, Utilisation category DC13
24 VDC
Current leakage Ir
0.5 mA
Interfering radiation
IEC 61000-6-4

RSS 36-I2-SD-ST Related Documents